W 2300 Series PTO Shaft Replacement of Walterscheid
- Length: 1410mm
- End 1 1 3/4" Six Spline Yoke
- End 2 1 3/4" Six Spline K34 Clutch, 100Nm
- Tubing: 0v / 1
- Guard: SD15
- Max. dynamic capacity 540 rpmat a speed of 28 kW 500 Nm
Max. dynamic capacity at 1,000 RPM: 44 kW 415 Nm
Values at 5deg angle at work and service life of 1000 hours
LZ = length of slid-in in millimeters, between intersections
Specifications Of W 2200 Series PTO shaft
| Application scope |
- Mowers
- Harvesters
- Seeders
|
| Properties |
- Tractor-side 1-3/8" (6) shaft collar kit
- A time interval for lubrication ranging from between 50 and 100 hours
- Meets EC 993/392 EEC requirements
- Conforms to EN12965 safety standard
- CE mark available
|
| It consists of |
- Semi-clutch axle that has shielding
- Declaration of conformity
- Instruction manual
|
PTO Shafts Parts and components
EVER-POWER's PTO components and shafts can keep your equipment running. As a top supplier of PTO shafts, we carry various standard constant velocity, metric, and drivetrains, and PTO shaft components and assemblies (implement clutches, yokes, oil lines). We also offer drop-in replacement drivetrains and parts that offer a simple solution to customize or repair your system. Ever-power has a wide selection of CV PTO shaft drivetrains.
| |
|
|
|
| Tractor Yoke |
Cross and Bearing Kit |
Shaft |
Shaft Weld Yoke |
| |
|
|
|
| Slip Sleeve |
Tube |
Tube Weld Yoke |
Implement Yoke |
| |
|
|
|
| Yoke & Shaft Assembly |
Yoke & Tube Assembly |
Drivelines |
Guard & Guard Bearing |
PTO Control on a Farm Tractor
Transmission
The most basic and earliest version for PTO can be described as a gearbox PTO. This PTO shaft has been directly linked directly to the tractor's gearbox. The PTO is only operational when the clutch of the tractor is engaged. If you take your tractor in gear and it is it is slowing down it will stop working. PTO will cease working. This is an issue when it comes to lawn mowing.
Transmission PTOs typically need an overrunning gear. If they do not have it, an un device that is driven (such as the blade of a lawn mower) could apply force on the PTO shaft because of inertia. This would transfer force onto the transmission. The device is able to "drive" to the tractor and, using the drive clutch of the tractor it will continue moving. The PTO overrunning gear stops this by permitting to allow the PTO shaft to move freely in a single direction. In the latest models, it is integrated inside the tractor. For older models this is an extra piece of equipment that is mounted on the PTO shaft.
Live (two-stage clutch)
The live PTO runs on the two-stage clutch. By pressing the clutch halfway, you will disable the transmission. However, pressing it fully will disable the transmission as well as the PTO. This allows the driver to reduce speed or shift gears even though the PTO is operating.
Independent
Independent PTO is the term used to describe PTO shaft is controlled independently. PTO shaft can be controlled through a separate clutch. Similar to the live PTO it also allows full control of the tractor as well as managing the PTO in its own way. There are two types of freestanding PTOs: hydraulic and mechanical. Apart from the PTO lever and the PTO lever, the mechanically independent PTO utilizes a different switch selector. Typically, the tractor needs to be shut off or stopped to alter the position of this selector. Hydraulic Independent PTO uses a single selector.
PTO Shaft for Agricultural Gearbox
Equipment for agriculture, such as combiners, tractors and harvesters utilize their own PTO shaft. These parts are subject to extreme stress and loads and it is crucial to understand why they have failed in the first place. Continuous compressing of the shaft could cause damage to connecting shafts, and possibly the tractor and the equipment. A PTO shaft that is used for the agriculture gearbox is an essential part of an agricultural tool or tractor. PTO shafts for agricultural gearbox is protected by an safety shield on each end and is used on tractor and implements. A PTO shaft is able to be welded to the drive side making use of a universal joint while the rear shaft may be joined directly into the tractor.
Why should you select Us?
1. Professionally manufactured and sold agricultural equipment for over 20 years.
2. "ever-power" as well as "HZPT" is manufactured in China.
3. Certification
4. We ensure that we have strict quality control and ensure the highest level of service to our customers.
5. We provide top-quality and quick after-sales services.
6. Our goal is to win.
7. We are able to design and manufacture machines that meet our customer's requirements.
8. We've developed a variety in replacement components for Japanese tractor models and can supply the parts along with the tractor.
